1. <em id="w3j4w"><ruby id="w3j4w"></ruby></em>
      2. <th id="w3j4w"></th>

          超聲波風速儀,位置傳感器,液位傳感器,超聲波風速風向儀,便攜式氣象站,玻璃車床,放射性檢測儀,顆粒物采樣器,玻璃金屬封接設備,氣體流量校準儀

          產品資料
          產品[

          玻璃**

          ]資料
          如果您對該產品感興趣的話,可以 產品名稱: 玻璃**
          產品型號: 148/10/100 WS WK
          產品展商: Arnold
          關注指數:3559
          產品文檔: 無相關文檔

          簡單介紹

          148/10/100 WS WK 機器盒式噴燈-玻璃**,表面混合,水冷 為氫氣和氧氣 盒式噴燈總長:500mm, 盒式噴燈火焰寬度:100mm。10排噴嘴。該玻璃**優點:低噪音。穩定一致的火焰。極高的熱容量。適合加工石英玻璃。 可用于石英擴管機和旋盤機上。

          玻璃**

             的詳細介紹

          德國ARNOLD提供上等的148/10/100 WS WK  機器盒式噴燈-玻璃**,表面混合,水冷

          為氫氣和氧氣

          盒式噴燈玻璃**總長:500mm, 盒式噴燈火焰寬度:100mm。10排噴嘴。

          該玻璃**優點:低噪音。穩定一致的火焰。極高的熱容量。適合加工石英玻璃??捎糜谑U管機和旋盤機上。
           

          玻璃**技術信息Important information for this type of burner:

          1.The connections of the media as well as the cooling water supply are shwon at the following layout.
          供水冷和供氣

            1.1  Especially at the gas connection it has to be regarded that there is a screwing with left-handed   thread in order to avoid any confusion. 
            The gas pipe – 12 mm diameter – also served as clamping for a burner holder.
                    
          螺紋**氣管,  氣管管徑 -12mm,
          1.2 
          It is not permitted to operate the burner without water cooling.
            In order to guarantee the burner cooling, the water flow temperature should be around 20°C.
            If the flow temperature is less than 20°C there can be formed condensation water. 
            The outlet temperature of the water depends on the power (flame intensity) of the burner. But   it should never be mor than 50 °C. 
                     玻璃**
          必須要水冷, 水流溫度約20°C。如果低于20°C,會產生冷凝水。出口水溫取決于噴燈火焰強度。但不應超過50 °C。

          1.Flame width and flame adjustment
          火焰寬度和調整
          2.1  Due to the small long flame zone the burner can be used for joining processes as well as for   forming processes. The burner only has to be turned by 90 ° in the burner holder.
                    
          由于小而長的熱區,噴燈可用于焊接和成型工作。噴燈要轉90 °在噴燈支架。
          2.2  At the flame adjustment it has to be regarded that the oxygen ratio is not too less. Thus the   flame is directly pulled into the burner nozzles. The highest flame temperature is then at this   area. This can lead to overheating and burning of the nozzles.

                              火焰調整氧氣率不能太小?;鹧鏁苯永雵娮?。高火焰溫度在該地方。這導致過熱,燒毀噴嘴

          產品留言
          標題
          聯系人
          聯系電話
          內容
          驗證碼
          點擊換一張
          注:1.可以使用快捷鍵Alt+S或Ctrl+Enter發送信息!
          2.如有必要,請您留下您的詳細聯系方式!

          聯系我們
          產品目錄
          Copyright? 2003-2022  培德國際有限公司上海代表處版權所有   聯系人:盧先生  聯系電話:021-62794500, 021-62790588
          傳真號碼:021-62792664 公司地址:上海市北京西路1277號國旅大廈1707室
            
           
          亚洲码欧美码一区二区三区

            1. <em id="w3j4w"><ruby id="w3j4w"></ruby></em>
            2. <th id="w3j4w"></th>